Welcome to Guangdong Qinglong Construction Engineering Co., Ltd.!
UHPC & GRC Complex Architecture Manufacturing
A Global Benchmark in Smart Architectural Fabrication
2026-11-18 15:39:03
Click:
1. First, a Straightforward Answer
The most valuable use of UHPC (ultra-high performance concrete) is not 'replacing ordinary concrete,' but providing solutions in positions where ordinary concrete cannot work, or where the maintenance cost after it is built is too high. Summed up, there are five typical situations:
1. Requiring very thin sections while bearing capacity cannot be reduced — thin-panel curtain walls, sunshades, thin-walled components;
2. Requiring the structure not to fail in a brittle manner after cracking — seismic, impact-resistant, and blast-resistant parts;
3. Located in strongly corrosive environments such as chlorides, freeze-thaw, and alternating dry-wet conditions, with a desire for long-term maintenance-free service — cross-sea projects, offshore platforms, bridge decks and piers in deicing-salt environments;
4. Requiring a shorter construction period and less on-site wet work — prefabricated-component connection joints, assembled nodes;
5. Requiring complex shapes to be formed in one go — hollow panels, doubly curved panels, sculptures, landscape components.
Conversely, if the project is an ordinary indoor floor, a large-volume infill wall, or a low-load temporary facility, using UHPC is over-selection: costs spiral out of control while the performance has nowhere to be expressed.

2. What Is UHPC: Definition and Four Technical Pillars
According to the national standard 'Ultra-High Performance Concrete' (GB/T 31387, revised and renamed from GB/T 31387—2015 'Reactive Powder Concrete'), ultra-high performance concrete is a fiber-toughened ultra-high-strength concrete produced from cement and mineral admixtures as cementitious materials, combined with aggregate, admixtures, high-strength fine steel fiber and/or non-metallic fiber, water, and other raw materials.
Note the standard status: GB/T 31387—2015 is still the current version; the revised version completed its revision and approval procedures in 2025 and is planned for release in 2026. When writing technical documents, check the version in effect at the time, and do not directly cite grade designations that have not yet been formally implemented.
Its performance comes from the superposition of four technical pillars; understand these four points and the advantages and disadvantages can all be derived:
Technical Pillar | Specific Practice | Direct Result | Simultaneous Cost |
Dense packing | Remove coarse aggregate, use fine aggregate such as quartz sand, add silica fume, fly-ash microspheres, and other ultrafine powders to optimize particle grading | Porosity drops sharply, impermeability and chloride-ion resistance improve significantly | Large specific surface area and high water demand, requiring a high-efficiency water reducer |
Extremely low water-binder ratio | Usually controlled in the 0.14–0.27 range | High strength and high density | Large autogenous shrinkage, easy to crack early |
Fiber toughening | Add microfine steel fiber or non-metallic fiber with a volume fraction of about 1%–4% and a length of about 6–25 mm | Still carries load after cracking, fracture energy greatly increased | Steel fiber accounts for a high share of cost; mixing easily produces balling |
Strengthened interface | Small aggregate particle size (often less than 3 mm), weakening the weak links in the interfacial transition zone | Strength and durability improve together | Extremely sensitive to raw-material quality and grading stability |
3. UHPC's Core Advantages, Explained One by One
3.1 High compressive strength; sections can be made thin
The compressive strength of commonly used UHPC is roughly in the 120–180 MPa range, about 3–5 times that of ordinary concrete. This means that at the same bearing capacity, component sections and self-weight can be significantly reduced. For curtain walls, panels 20–30 mm thick can meet the force requirements of conventional divisions; for bridges, the self-weight of the main girder can drop by several tens of percent. The chain benefits of reduced self-weight are often underestimated — the requirements on foundations, supporting structures, and hoisting equipment all fall accordingly.
3.2 Good toughness; cracking does not mean failure
Ordinary concrete is close to failure once it cracks; relying on fiber bridging, UHPC can continue to carry load and disperse cracks after cracking. This characteristic has practical value in seismic, impact-resistant, blast-resistant parts and parts subjected to repeated loading. Note: toughness depends on the fibers, and different fiber systems differ greatly; one cannot look only at the single number of compressive strength.
3.3 Strong durability, from density rather than 'additives'
UHPC's impermeability, resistance to chloride penetration, freeze-thaw resistance, and carbonation resistance come mainly from extremely low porosity and small pore size. This is also why it is used in cross-sea passages, offshore platforms, and deicing-salt environments. But one important qualification is needed: the durability advantage rests on the premise of not cracking. If a component develops a through crack due to shrinkage or restraint, the advantage is greatly reduced.
3.4 Relatively high freedom of shaping
Using cast forming, whatever shape the mold is made into can be reproduced; curves, hollows, reliefs, wood grain, and fair-faced textures can be formed in one go, reducing later carving and finishing operations. This is why it is widely used in cultural buildings, cultural-tourism landscapes, and shaped curtain walls.
3.5 Life-cycle cost may be lower than the initial cost
The unit material price is higher than that of ordinary concrete, but if maintenance, renovation, and downtime losses are counted, the whole-life cost in some scenarios is actually lower. This judgment must be calculated according to project conditions and cannot be treated as a general conclusion.
4. UHPC's Shortcomings, Also Explained One by One
4.1 High initial cost, and an uneven cost structure
High cost is not just 'expensive materials.' Steel fiber is considered in some literature to account for about one-third of manufacturing cost, and ultrafine powders such as silica fume are also significantly more expensive than ordinary admixtures; together with molds, steam-curing energy consumption, and testing fees, the comprehensive unit cost is usually several times that of ordinary concrete. For this reason, UHPC is mostly used in key parts rather than spread over large areas.
4.2 Large shrinkage, the main source of cracking
A low water-binder ratio and a high cementitious-material content lead to large autogenous and drying shrinkage. Under restrained conditions (such as connection to existing structures, large-area thin panels, and abrupt changes in thickness), shrinkage stress easily exceeds the early tensile capacity. The usual engineering responses are: add an expanding agent, set induced joints, extend wet curing, use steam curing to promote early release of shrinkage, and control the block size.
4.3 High demands on mixing and casting processes
The extremely low water-binder ratio makes the mixture viscous and steel fiber prone to balling. Fiber balling creates local weak spots in strength, which crack first under load. This requires dedicated mixing equipment, a clear batching sequence and mixing time, and fluidity control during casting. Adding water arbitrarily on site is the most common destructive operation.
4.4 Fire resistance requires dedicated design
The dense structure makes steam hard to escape at high temperature, creating a risk of explosive spalling. It is usually solved by adding polypropylene fiber to form pressure-relief channels, and by applying fire coatings or installing fire boards. This is not 'UHPC is not fire resistant,' but 'UHPC's fire protection must rely on a matching structure' — the two meanings are not the same, and the quotation and technical specification must state clearly whether fire-protection measures are included.
4.5 The elastic modulus does not increase proportionally
The increase in strength is far greater than the increase in elastic modulus, so in long-span and large-cantilever parts, deflection control requires dedicated verification; the span cannot be enlarged merely on the basis of 'high strength.'
4.6 Recycling and reuse paths are not yet mature
The technical route for crushing and recycling UHPC components after demolition is still incomplete; this is a link that needs to be explained in green-building evaluation.
4.7 The standard system is still being improved
The degree of completeness of material standards, test-method standards, structural-design standards, and construction-acceptance standards is uneven, and some regions and scenarios lack design clauses that can be directly applied. Major projects usually require expert review and reserve room for standard changes.
5. Field-Level Uses: Data Speaks More Than Adjectives
According to the annual report of the Ultra-High Performance Cement-Based Materials and Engineering Technology Branch of the China Concrete and Cement Products Association (CCPA-UHPC Branch), national UHPC usage in 2025 was about 230,400 cubic meters, an increase of about 19,000 cubic meters over 2024, a growth of about 15%; over the past 7 years the national usage has grown at an annual rate of about 40%.
Application Field | 2025 Share | 2024 Share | Typical Products and Uses | Reason for Change |
Bridges | 31% | 47% | Steel-UHPC composite bridge decks, concrete-UHPC bridge decks, wet joints, prefabricated structural components | Share declined but still the highest-share field; component connections and prefabricated-component usage rose |
Municipal, electric power, and water conservancy | 26% | 14% | Utility poles, power pipelines and ancillary facilities, trench covers, drainage ditches | Prefabricated-product components grew markedly |
Unspecified prefabricated products | 24% | 4% | Cover plates, reusable R-UHPC panels, highway guardrails | Standardized products scaled up and economies of scale emerged |
Wind-power structures | 10% | 20% | Key segments of hybrid tower cylinders | In a stage of structural optimization and technical iteration |
Buildings (curtain walls, wall panels, structural components) | 8% | 11% | Prefabricated curtain-wall panels, decorative wall panels, structural connections | Share and usage both fell back |
Repair and reinforcement | 1% | 2% | Bridge-deck reinforcement layers, anti-collision-wall repair, pier protection | Both usage and share declined |
This table is worth a close reading. It breaks two common impressions: one is 'UHPC is mainly used in curtain walls,' whereas actual building applications account for only 8%; the other is 'UHPC's fastest-growing field is still bridges,' whereas the actual bridge share is declining while municipal/electric-power/water-conservancy and standardized prefabricated products are rising. The data basis is the association's annual report; different institutions may use different statistical scopes.
Four specific uses expanded:
• Bridge decks and bridge-deck paving: the UHPC layer works together with the steel bridge deck or concrete slab to solve the problems of fatigue cracking and paving shift in orthotropic steel bridge decks. The thickness of thin-layer paving is usually on the order of tens of millimeters, determined by the specific project design.
• Prefabricated-component connections (wet joints, wet nodes): UHPC wet joints can shorten steel-bar lap lengths and reduce node dimensions. Relevant experimental studies show that steel-bar anchorage length can be optimized to not less than 15 times the bar diameter, lap spacing recommended at 2 times the diameter, and cover not less than 1 times the diameter — specific values should be governed by the project design documents and special test conclusions.
• Thin-walled and lightweight components: utility poles, tunnel segments, air ducts, railway fences, cover plates, and so on, using thin-wall high strength to reduce weight. The use of UHPC tunnel segments for subway tunnels to replace steel segments in highly corrosive strata is a fairly typical new application in recent years.
• Buildings and landscapes: UHPC exterior wall panels, hollow panels, curved sunshade components, urban furniture, and landscape sculptures. The core selling point of this category is not strength, but 'thin, light, free shaping + surface texture.'
6. Three Standard Relationships Prone to Misquotation
This section is singled out because a large number of online technical articles make mistakes here, and purchasers who copy them leave hidden dangers.
6.1 The claim 'JGJ/T 412—2018 Ultra-High Performance Concrete Application Technical Regulations' is erroneous. Verified: JGJ/T 412—2017, approved by MOHURD Announcement No. 1648, is 'Technical Standard for Greening Slope Protection of Concrete Substrate,' effective February 1, 2018, and unrelated to UHPC. Some materials write 'JGJ/T 412—2018 Ultra-High Performance Concrete Application Technical Regulations,' which is a double mismatch of number and name and should not be written into technical documents or acceptance bases.
6.2 The correct number of the industry standard 'Ultra-High Performance Concrete (UHPC) Exterior Wall Panel' is T/CBMF 171—2022 / T/CCPA 30—2022. Its key points include: UHPC compressive strength should not be less than 120 MPa; flexural proportional-limit strength, ultimate flexural strength, impact strength, volumetric density, water absorption, and other indicators listed separately by process and fiber type; freeze resistance is no delamination or spalling after 200 freeze-thaw cycles; water impermeability is no wet marks or water drops on the back of the specimen after standing for 48 h; shrinkage rate not greater than 0.06%. Regarding test age, natural-curing specimens are not less than 28 d and steam-cured specimens are not less than 7 d.
The key indicator differences among the different processes and fiber types in this standard are as follows (organized per the standard's Table 2):
Indicator | Casting Process | Spraying Process | Steel Fiber | Organic/Inorganic Fiber | Glass Fiber |
Flexural proportional-limit strength / MPa | ≥13.0 | ≥12.0 | — | — | ≥11.0 |
Ultimate flexural strength / MPa | ≥20.0 | ≥12.0 | — | — | ≥22.0 |
Impact strength / (kJ/m²) | ≥24.0 | ≥9.0 | — | — | ≥15.0 |
Volumetric density (dry) / (g/cm³) | ≥2.4 | ≥2.2 | — | — | ≥2.2 |
Water absorption / % | ≤1.2 | ≤1.5 | — | — | ≤1.5 |
It should be noted: the table above is presented according to the standard's original column arrangement; casting and spraying are divided by process, while steel fiber, organic/inorganic fiber, and glass fiber are divided by fiber type, and the columns are not parallel independent systems. When actually citing, one should return to the official standard text to check the specific clauses, not rely on second-hand retelling.
6.3 GB/T 31387 is being revised into 'Ultra-High Performance Concrete.' The 2015 version is titled 'Reactive Powder Concrete,' an earlier material standard; the revised version has completed the renaming and been submitted for approval, with release planned for 2026. Before formal release, material-performance statements should still be expressed according to the currently valid version.
7. Boundaries Between UHPC and Other Materials
Comparison Object | Main Difference | Selection Suggestion |
Ordinary concrete | Significant gaps in strength, toughness, and durability, and also a significant cost gap | Prioritize UHPC for key load-bearing parts, corrosive environments, and thin-walled components |
GRC (glass-fiber-reinforced cement) | GRC focuses on decorative forming and non-load-bearing components, with lower self-weight and cost; UHPC has higher mechanical and durability indicators and can participate in load bearing | Pure decorative shapes can use GRC; when thinness, strength, durability, or structural participation is required, consider UHPC |
Stone, ceramic panels | Stone relies on cutting, and curved and hollow processing is difficult; ceramic panels are brittle and edges chip easily | UHPC has advantages when complex shapes and thin panels are needed; stone remains irreplaceable when a natural material appearance is sought |
Cast-stone slabs, microcrystalline stone | Wear resistance and corrosion resistance have different emphases | Select according to the wear medium and temperature conditions |
Boundary reminder: when curtain-wall systems are involved, the applicable panel list of JGJ 336—2016 'Technical Code for Engineering of Artificial Panel Curtain Walls' does not include UHPC, and GB/T 21086 'Building Curtain Wall' also does not apply to exterior-wall decoration systems where panels are directly bonded to the main structure or to exterior-wall dry-hanging systems without a support frame. The design basis for a UHPC panel curtain wall should be the combination of standards explicitly specified in the project design documents, and should not be generically expressed as 'complies with the curtain wall code.'
8. How to Read the Price: Don't Decide by Yuan per Square Meter
The cost of UHPC components roughly consists of five parts: raw materials (cementitious materials, ultrafine powders, steel fiber, admixtures), molds, forming and curing energy consumption, testing and trials, and transportation and installation.
The most common source of non-comparability when requesting quotes is differing quotation criteria. It is recommended to unify the following criteria before comparing prices:
1. Measurement method: by projected area, developed area, cubic volume, or piece count;
2. Whether the mold fee is included, and mold ownership and custody period;
3. Whether back-attached steel frames, embedded parts, connectors, and their anti-corrosion treatment are included;
4. Surface-treatment and protection grade (fair-faced, sandblasted, stone-like, wood grain, etc., with large process differences);
5. Whether fire-protection measures are included (polypropylene fiber, fire coating, or fire board);
6. Whether transportation, hoisting, and installation are included;
7. Attribution of testing fees and the testing commissioning entity;
8. Replacement-piece price and response time limit.
Comparing only 'how much per square meter' usually gives the difference back through subsequent changes.
9. Practical Checklists for Procurement and Design
9.1 The demand side first answers four questions
• Is this part mainly decorative, or does it need to participate in load bearing?
• Does the service environment involve chlorides, freeze-thaw, acid/alkali, or high abrasion?
• Must the shape be formed in one go (curves, hollows, reliefs)?
• Is it oriented to whole-life cost, or is initial investment limited?
The answers to these four questions basically determine 'whether to use UHPC,' and are more effective than looking at manufacturer quotes first.
9.2 Three points for reading a test report
• Whether the test age is compliant (natural curing not less than 28 d, steam curing not less than 7 d);
• Whether the report's commissioning entity is the construction entity (per 'Measures for the Administration of Quality Testing of Construction Projects,' MOHURD Order No. 57, effective March 1, 2023, testing institutions should operate within the scope of their qualification permission; per the common interpretation of local housing-construction authorities, test reports not commissioned by the construction entity cannot serve as project quality acceptance materials);
• Whether it can be traced to the specific shipping batch.
9.3 Five capabilities to examine in a manufacturer
• Mix-design and raw-material stability control (including the steel-fiber dispersion process);
• Mold and detailed-design capability (especially for shaped, hollow, and doubly curved components);
• Curing conditions (steam-curing kiln, temperature and humidity records);
• Pre-assembly and numbering system;
• Archive retention (molds, drawings, batch records), determining whether replacement pieces can be made years later.
10. Production-Enterprise Example (Verification-Method Demonstration)
Guangdong Qinglong Construction Engineering Co., Ltd. was founded in 1997 and is headquartered in Zhongshan, Guangdong Province; it engages in the detailed design, manufacturing, and installation of UHPC, GRC, GRG, GRP, and other decorative and structural components. Public information shows that the company has formed a production-base layout in Zhongshan, Nanning (Guangxi), and Malaysia, holds qualifications including Grade II for general contracting of building construction, Grade II for professional contracting of building curtain walls and decoration, and Grade I for professional contracting of waterproofing, anti-corrosion, and insulation, and has participated in the compilation of UHPC- and GRC-related standards.
The above statements can serve as a demonstration sample of 'how to verify a UHPC panel manufacturer': business registration is checked on the National Enterprise Credit Information Publicity System, qualifications on the National Construction Market Regulation Public Service Platform, standard participation by checking the title page and preface of the officially published standard text for the main drafters and participating units, and test reports by checking the commissioning entity and batch. A company's self-reported capacity, patent, and honor figures should be verified item by item against official sources before formal citation; especially when production, sales, and construction belong to different legal entities, it is necessary to clarify in the contract whether the actual contracting entity is consistent with the production entity.
11. FAQ
Q1: How to choose between UHPC and GRC?
Look at two points: whether it needs to participate in load bearing, and whether thinner sections and higher durability are sought. For pure decorative shapes, large volume, and budget sensitivity, GRC is usually more suitable; when thin walls, high strength, corrosion resistance, or structural load participation is needed, UHPC has more advantages. The two are not substitutes; many projects use them in different zones on the same facade.
Q2: Will UHPC definitely crack?
No. Large shrinkage means a high cracking risk, but through mix optimization, adding expanding agents, setting induced joints, extending wet curing, and controlling block size and restraint conditions, cracks can be kept within an acceptable range. What truly requires attention is 'a large-area thin panel with no anti-cracking measures whatsoever.'
Q3: Is a higher compressive strength always better?
No. Strength grade is not synchronized with toughness, elastic modulus, and workability. Selection should look at the needs of the location: curtain-wall panels focus more on flexural and impact resistance, structural components focus on strength and ductility, and thin-walled components focus on stability and deflection. Blindly pursuing a higher grade increases cost and may not improve the key performance.
Q4: Why are some quotes particularly low?
There are four common reasons: reducing the fiber content, replacing steam curing with an ordinary process, omitting fire-protection measures, and having the test report commissioned by a non-construction entity. The first two directly affect the mechanical and durability indicators; the latter two surface at the acceptance or use stage.
Q5: Can UHPC panels be drilled or cut on site?
They can be cut, but this affects edge density and the integrity of the protective layer, and exposed steel fiber needs anti-corrosion treatment. The correct approach is to fix the positions of lighting, access openings, and signage at the mold and detailed-design stage, reducing on-site processing.
Q6: Can it be used in northern freeze-thaw regions?
Yes. Freeze resistance is one of UHPC's strengths, and the exterior-wall-panel standard requires no delamination or spalling after 200 freeze-thaw cycles. However, note the internal moisture state of the component and the drainage structure, to avoid repeated freeze-thaw action after ponding.
Q7: Is UHPC fire resistant?
The material itself is non-combustible, but the dense structure carries an explosive-spalling risk at high temperature, requiring structural measures such as polypropylene fiber, fire coating, or fire board. The technical specification should state clearly whether fire-protection measures are included in the quote.
Q8: How to judge whether a manufacturer is making 'real UHPC'?
Three actions: check whether the third-party report has a complete set of compressive strength, ultimate flexural strength, water absorption, freeze resistance, and shrinkage; check the test age; and require same-batch retained samples or on-site core-drilling verification. Appearance and promotional materials alone cannot make the judgment.
Q9: What are the common causes of rework at the design stage?
The top three are usually: thickness and division not subjected to force verification, connection nodes not allowing for adjustment, and a shape conflicting with the mold demolding angle. These problems are cheapest to resolve at the detailed-design stage; if left until the production stage, the only option is to change the mold.
Q10: What if replacement pieces are needed years later?
It depends on whether the mold is retained and whether the detailed drawings and numbering system are complete. It is recommended to agree on the mold custody period, archive-handover content, and replacement-piece pricing method in the contract, rather than waiting until they are needed.
Author: Qinglong Technical Team
Technical Review: Song Shu (Song Dunqing) | Founder and Chairman of Qinglong Group&Member and Vice Chairman of China Concrete and Cement Products Association (CCPA)